Messages¶

Observing the traffic on the bus we can see there are different units. These are the SRC address found on the 12 bus :

ADDRESS	UNIT
41	Hi-Mit remote controller
47	Hi-Mit remote controller
50	Indoor Unit
57	Hi-Mit remote controller
63	Hi-Mit remote controller
34
35	Outodoor Unit
#Address-146	Indoor Unit
242
243

REQUESTS / REPLIES ANALYSIS¶

Here I try to report any communication pattern I can find :

41 - 146 interaction¶

Messages exchanged between Hi-mit interface and indoor unit
WIP

Status update request¶

Every 60s there is a status update request from 41. The request is acknowledged and replied to from 146.

|41|0|9|202|161|9|1|97|11|
ACK from 146
|146|0|48|9|1|9|0|97|62|0|8|1|6|12|45|28|0|0|0|24|28|28|28|28|28|28|28|0|0|0|0|224|0|0|0|0|0|0|0|0|0|0|0|0|0|0|0|184|
ACK from 41

Working mode change on master controller¶

When there is a change of the working mode on the master controller if leads to a parameters update message from 146.The message is ackowledged from 41.

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	-	MODE:	VALUE	CYCLE1 SET TEMP:	VALUE	CYCLE2 SET TEMP:	VALUE	ROOM1 SET TEMP:	VALUE	ROOM? SET TEMP:	VALUE	ROOM? SET TEMP:	VALUE	ROOM? SET TEMP:	VALUE	ROOM? SET TEMP:	VALUE	ROOM? SET TEMP:	VALUE	CRC
146	0	32	9	1	9	0	99	62	1	8	3	6	4	12	10	23	11	28	12	28	13	28	14	28	15	28	16

ACK from 41

47 - 242 interaction¶

|47|0|10|202|160|1|1|108|0|12|
ACK from 242
|242|0|48|1|1|1|1|108|62|0|31|129|129|27|0|0|0|0|0|0|0|22|0|0|0|0|0|0|0|20|60|50|7|24|25|129|129|0|100|3|0|0|8|0|4|0|0|7|
ACK from 47

50 - 35 interaction¶

|50|0|9|1|1|1|0|240|248|
ACK from 35
|35|0|36|1|0|1|1|255|0|40|32|0|0|0|2|0|3|34|128|31|0|31|128|18|170|0|0|0|41|41|1|3|241|208|0|106|
ACK from 50
|50|0|28|1|1|1|0|255|24|32|0|7|24|33|129|34|30|30|0|0|25|0|62|0|6|0|2|100|
ACK from 35
|35|0|14|1|0|1|1|254|16|32|16|32|0|241|
ACK from 50
|50|0|32|1|1|1|0|159|31|129|129|20|60|0|7|129|31|26|100|3|0|0|0|0|0|0|0|0|0|2|0|111|
ACK from 35

63 - 243 interaction¶

|63|1|9|202|160|1|0|0|99|
ACK from 243
|243|1|48|1|0|0|255|192|6|0|0|2|0|0|0|0|0|0|0|0|0|66|34|18|178|0|0|60|20|31|0|9|31|0|145|0|0|0|0|33|0|24|0|30|0|0|0|92|
|63|1|9|202|160|1|0|1|98|
ACK from 243
|243|1|48|1|0|0|255|193|6|0|0|0|0|26|0|0|0|0|7|0|0|0|129|0|0|0|31|0|0|100|31|0|0|0|0|3|129|0|0|0|0|0|129|0|0|0|0|243|

DEVICE DISCOVERY¶

When the Hi-mit interface is looking for devices on H-LINK bus the following messages are sent: (This messages were logged with no device connected on H-LINK bus)

SRC	CTRL	LEN		DSW1 ADDR				CRC
41	0	9	202	160	255	255	241	146

SRC	CTRL	LEN		DSW1 ADDR					CRC
57	3	10	202	160	255	255	0	0	99

AUTODISCOVERY ??¶

From time to time these messages appears on the bus, they are not always grouped together and they are not acknowledged, maybe they are used to report their presence ?

|35|0|10|1|0|1|255|15|20|238| <- UPDATE: VALUE 15 & 20 CHANGE OVER TIME, ARE THEY TEMPERATURE ?
|50|0|9|1|1|1|255|241|6|
|41|0|9|202|160|255|255|241|146|

|35|0|28|1|0|1|255|242|3|34|128|31|0|31|128|18|170|0|0|0|41|41|1|3|241|208|0|171| -> This is a status update but it seems no one requests or acknowledge

ALL MESSAGES¶

Here are reported all the messages captured :

Note: DSW8 ADDR field is the binary encoded value +1
Example:

In the image above DSW8 ADDR is equal to 8+1 = 9

DSW1 field is thebynary encoded value set on the Hi-mit interface

ADDRESS 41 ( HI-MIT INTERFACE )¶

Request (KEEP ALIVE/ DISCOVERY ?) sent every 30s.

SRC	CTRL	LEN		DSW1 ADDR				CRC
41	0	9	202	160	255	255	241	146

Status update request sent every 60s. Acknoledged from 146.

SRC	CTRL	LEN		DSW1 ADDR	DSW8 ADDR			CRC
41	0	9	202	160	1	1	97	2

Request sent when there is a remote command.

SRC	CTRL	LEN		DSW1 ADDR																																											CRC
41	0	48	202	160	1	1	107	62	31	8	255	11	12	45	24	0	0	26	28	28	28	28	28	28	28	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	211

Request sent when there is a remote command.

SRC	CTRL	LEN		DSW1 ADDR																																											CRC
41	0	48	202	160	1	1	107	62	0	8	0	11	12	45	24	0	0	26	28	28	28	28	28	28	28	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	51

Address 146¶

Messages coming from 146 seems to be associated with machine operation parameters that could be stored in the INDOOR UNIT. This is the common header:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	OP	-
146	0	xx	1	1	1	0	99	62

OP is set to 99 when the message is generated by a single or multiple parameters update; it is set to 97 when it provides a status update in reply to a request from 41.

For example the following message is sent when there is a parameter change made on the master controller:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	OP	-	PARAMETER ID	SET VALUE	CRC
146	0	12	1	1	1	0	99	62	x	x	xx

Multiple parameters can also be concatenated in a message in the following way:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	OP	-	PARAMETER ID 1	SET VALUE 1	PARAMETER ID 2	SET VALUE 2	PARAMETER ID n	SET VALUE n	CRC
146	0	10+(n*2)	1	1	1	0	99	62	xx	xx	xx	xx	xx	xx	xx

PARAMETERS ID¶

These are the parameters ID :

DESCRIPTION	PARAMETER ID
MODE	1
CYCLE MODE?	2
CYCLE1 WATER TEMP	3
CYCLE2 WATER TEMP	4
DHW SET TEMP	5
POOL SET TEMP	6
ERROR CODE	7
?	8
?	9
CYCLE1 ROOM1 SET TEMP	10
CYCLE1 ROOM2 SET TEMP ?	11
CYCLE1 ROOM3 SET TEMP ?	12
CYCLE1 ROOM4 SET TEMP ?	13
CYCLE2 ROOM1 SET TEMP ?	14
CYCLE2 ROOM2 SET TEMP ?	15
CYCLE2 ROOM3 SET TEMP ?	16
CYCLE2 ROOM4 SET TEMP ?	17
ROOM ENABLE	18
ROOM ECO MODE?	19
DHW CONFIG ?	20
PUMP STATUS	21
WATER PUMP CONFIG?	22

MODE¶

BIT 7	BIT 6	BIT 5	BIT 4	BIT 3	BIT 2	BIT 1	BIT 0
	HEAT MODE			COOL MODE	AUTO MODE	CYCLE 2 ENABLE	CYCLE1 ENABLE

This parameter sets the working mode of the unit: HEAT / COOL / AUTO. Only one of the 3 mode can be active at a time.

CYCLE MODE: 16 (CYCLE1 ECO MODE OFF),17 (CYCLE1 ECO MODE ON)¶

BIT 7	BIT 6	BIT 5	BIT 4	BIT 3	BIT 2	BIT 1	BIT 0
?	?	?	PUMP ENABLE ?	?	?	CYCLE2 ECO MODE	CYCLE1 ECO MODE

DHW CONFIG¶

0 DHW BOOST OFF, 128 DHW BOOST ON

PUMP STATUS¶

0 PUMP OFF, 128 PUMP RUNNING

WATERPUMP CONFIG? : SEEN VALUES: 32,128,160,192,224¶

192 ->(HEAT MODE SELECTED)

BIT 7	BIT 6	BIT 5	BIT 4	BIT 3	BIT 2	BIT 1	BIT 0
WP ECO MODE HEAT	WP ECO MODE COOL	1	0	0	0	0	0

STATUS UPDATE MESSAGE¶

This status update message is requested periodically from 41. OP is now set to 97

The parameter are in the same order as the table above: 1) MODE, 2)PUMP, 3) WATER SET TEMP, ETC ..

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR		OP	-		MODE	PUMP??	WATER SET TEMP CYCLE1	WATER SET TEMP CYCLE2	DHW SET TEMP	POOL SET TEMP	ERROR CODE			ROOM 1 SET TEMP								ROOM ENABLE		DHW CONFIG	PUMP STATUS	WATERPUMP CONFIG																CRC
146	0	48	1	1	1	0	97	62	0	8	0	11	12	45	24	0	0	0	26	28	28	28	28	28	28	28	0	0	0	0	160	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	242

EXAMPLES¶

These are some example messages

This is sent when the MASTER CONTROLLER POOL water set temp is changed to 27°C :

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR				POOL WATER TEMP	SET TEMP	CRC
146	0	12	1	1	1	0	99	62	6	27	77

This is sent when HEAT MODE is selected on MASTER CONTROLLER:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR					MODE ?																			CRC
146	0	30	1	1	1	0	99	62	1	64	3	20	4	20	11	22	12	22	13	22	14	22	15	22	16	22	17	22	24

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR						CRC
146	0	12	1	1	1	0	99	62	22	128	198

This is sent when COOL MODE is selected on MASTER CONTROLLER:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR					MODE ?																			CRC
146	0	30	1	1	1	0	99	62	1	8	3	13	4	16	11	28	12	28	13	28	14	28	15	28	16	28	17	28	71

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR						CRC
146	0	12	1	1	1	0	99	62	22	160	230

This is sent when AUTO MODE is selected on MASTER CONTROLLER:

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR					MODE ?																	CRC
146	0	28	1	1	1	0	99	62	1	4	3	28	11	0	12	0	13	0	14	0	15	0	16	0	17	0	80

ADDRESS 50 ( INDOOR UNIT )¶

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	CRC
50	0	9	1	1	1	0	240	248

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	CRC
50	0	9	1	1	1	255	241	6

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	-	MODE	PUMP ?	WATER SET TEMP	?	IDU GAS TEMPERATURE	-	IDU LIQUID TEMPERATURE	WATER OUT PHEX TEMP NOT SURE	WATER INLET TEMP										CRC
50	0	28	1	1	1	0	255	24	32	0	22	24	16	129	20	11	12	0	0	22	0	62	0	6	0	2	122

MODE is 32 when CYCLE 1 is OFF, when COOL MODE on CYCLE1 is enabled it changes to 9.
PUMP ? becomes 1 when cooling is enabled. Change to 17 when water pump is running. <- EDIT: NOT 100% SURE (PUMP SEEMS TO RUN EVEN WHEN PUMP=1 , MAYBE 1->CYCLE 1 ENABLED AND 17-> CYCLE1&ROOM1 ENABLED)
WATER SET TEMP IS SET WHEN CYCLE 1 IS ENABLED

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	WATER OUT TEMP ?			?			WATER SET TEMP		AMBIENT TEMP (SIMILAR VALUE)		REQUESTED PUMP PWM		FLOW ?									?		CRC
50	0	32	1	1	1	0	159	30	129	129	20	60	0	7	129	30	26	100	3	0	0	0	0	0	0	0	0	0	2	0	111

AMBIENT TEMP -> COULD BE TEMP SENSOR INSIDE INDOOR UNIT REPORTING A SIMILAR VALUE TO OUTDOOR AMBIENT TEMP
REQUESTED PUMP PWM -> I THINK IT IS REQUESTED PWM BECAUSE WHEN VALUE IS 100 (PWM 100 MEANS OFF) SOMETIME THE PUMP IS STILL ON
?->CYCLE1 HEAT ON : 4 CYCLE 1 HEAT OFF: 0, CYCLE 1 COOL ON: 6, CYCLE 1 COOL OFF: 2

ADDRESS 35 ( OUTDOOR UNIT )¶

SRC	CTRL	LEN	DSW8 ADDR		DSW8 ADDR				CRC
35	0	10	1	0	1	255	15	20	238

SRC	CTRL	LEN	DSW8 ADDR		DSW8 ADDR								CRC
35	0	14	1	0	1	1	254	16	32	16	32	0	241

SRC	CTRL	LEN	DSW8 ADDR		DSW8 ADDR						EVAP GAS TEMP		DISCHARGER TEMPERATURE		IDU LIQUID TEMP		FREQUENCE	CURRENT	EVO%								CRC
35	0	28	1	0	1	255	242	3	22	128	25	0	51	128	17	110	0	0	0	41	41	1	3	241	208	0	114

SRC	CTRL	LEN	DSW8 ADDR		DSW8 ADDR												OUTDOOR TEMP		EVAP GAS TEMP		DISCHARGER TEMPERATURE		IDU LIQUID TEMP		FREQUENCE	CURRENT	EVO%								CRC
35	0	36	1	0	1	1	255	0	40	32	0	0	0	2	0	3	20	128	22	0	42	128	14	100	0	0	0	41	41	1	3	241	208	0	178

Message similar to the previous one with added 8 byte.

|35|240|8|9|224|9|255|231| -> SENT WHEN THERE IS NO COMMUNICATION WITH OUDOOR UNIT ? LOOKS LIKE A DISCOVERY MESSAGE

ADDRESS 47 ( HI-MIT INTERFACE )¶

Unit 47 seems to send only this request that 242 replies to

SRC	CTRL	LEN	-	DSW1 ADDR	DSW8 ADDR	?	?	?	CRC
47	0	10	202	160	1	1	108	0	12

ADDRESS 57 ( HI-MIT INTERFACE )¶

This message is seen during device discovery

SRC	CTRL	LEN	-	DSW1 ADDR	?	?	?	?	CRC
57	3	10	202	160	255	255	0	0	99

ADDRESS 63 ( HI-MIT INTERFACE )¶

Unit 63 seems to only send request that 243 replies to. No other messages are captured at this time.

SRC	CTRL	LEN	-	DSW1 ADDR	DSW8 ADDR	?	?	CRC
63	1	9	202	160	1	0	0	99

SRC	CTRL	LEN	-	DSW1 ADDR	DSW8 ADDR	?	?	CRC
63	1	9	202	160	1	0	1	98

ADDRESS 242 (UNKNOWN)¶

SRC	CTRL	LEN	DSW8 ADDR	-	DSW8 ADDR	-	-	-		WATER TEMP			CYCLE1 ROOM1 TEMP ?								CYCLE1 ROOM1 SET TEMP											WATER SET TEMP						WATER PUMP SPEED		WATER FLOW (1 digit)		IDU CAPACITY?	?		?	?	CRC
242	0	48	1	1	1	1	108	62	0	7	129	129	27	0	0	0	0	0	0	0	22	0	0	0	0	0	0	0	20	60	50	20	24	12	129	129	0	14	3	14	0	24	2	4	1	1	111

ADDRESS 243 (UNKNOWN)¶

Unit 243 seems to reply to 63 requests.

SRC	CTRL	LEN	DSW8 ADDR	-	-	-	OP											FREQUENCY		TARGET FREQUENCY		OUTDOOR TEMP							DISCHARGER TEMP											FREQUENCE			EVAP GAS TEMP				CRC
243	1	48	1	0	0	255	192	6	0	0	2	0	0	0	0	0	0	0	0	0	64	30	17	159	0	0	60	20	30	0	1	30	0	145	0	0	0	0	34	0	24	0	29	0	0	0	68

SRC	CTRL	LEN	DSW8 ADDR	-	-	-	OP								FREQUENCE														WATER PUMP SPEED?												WATER FLOW?						CRC
243	1	48	1	0	0	255	193	6	0	0	0	0	26	0	0	0	0	7	0	0	0	129	0	0	0	29	0	0	100	29	0	0	0	0	3	129	0	0	0	0	0	129	0	0	0	0	243